specification rps -160-5 rps -160-12 rps -160-15 rps -160-24 rps -160-48 model dc voltage rated current (20.5cfm) rated power (convection) note.7 current range (20.5cfm) output voltage adj. range line regulation load regulation setup, rise time hold up time (typ.) voltage range note.6 frequency range power factor (typ.) efficiency (typ.) input inrush current (typ.) leakage current safety standards working temp. remote sense working humidity storage temp., humidity temp. coefficient vibration overload over voltage over temperature ac current (typ.) 5v 12v 15v 24v 48v 30a 12.9a 10.3a 6.5a 3.25a 0 ~ 20a 0 ~ 30a 0 ~ 9.1a 0 ~ 12.9a 0 ~ 7.3a 0 ~ 10.3a 0 ~ 4.6a 0 ~ 2.3a 0 ~ 6.5a 0 ~ 3.25a 103w 155w 112.2w 159.8w 112.5w 159.5w 113.4w 113.4w 161w 161w 100mvp-p 100mvp-p 120mvp-p 150mvp-p 250mvp-p ch1:4.5 ~ 5.5v ch1:10.8 ~ 13.2v ch1:13.5 ~ 16.5v ch1:22 ~ 27v ch1:43.2 ~ 52.8v 4.0% 3.0% 3.0% 2.0% 2.0% 0.5% 0.5% 0.5% 0.5% 0.5% 1.0% 1.0% 1.0% 1.0% 1.0% 1800ms, 30ms/230vac 3 at full load 500ms, 30ms/115vac 90 ~ 264vac 127 ~ 370vdc 16ms/230vac/115vac at full load 47 ~ 63hz pf>0.93/230vac pf>0.98/115vac at full load 85% 87% 87% 87% 88% 2a/115vac 1.1a/230vac cold start 35a/115vac 70a/230vac earth leakage current <300ua / 264vac, patient leakage current <100u a/264vac 105 ~ 135% rated output power 5.75 ~ 6.75v 110 (5v),105 (12v,15v,24v,48v) (tsw1 : d etect on heatsink of power transistor) 95 (5v),90 (12v,15v,24v,48v) (tsw2 : d etect on heatsink of power transistor) 13.8 ~ 16.2v 17.25 ~ 20.25v 27.6 ~ 32.4v 55.2 ~ 64.8v protection type : hiccup mode, recovers automatically after fault co ndition is removed protection type : shut down o/p voltage, re-power on to recover protection type : (tsw2)shut down o/p voltage, re-power on to recover protection type : (tsw1)shut down o/p voltage, recovers automatical ly after temperature goes down ansi/aami es60601-1, tuv en60601-1 approved -20 ~ +70 (refer to "derating curve") 5 ~ 15v 20 ~ 90% rh non-condensing -40 ~ +85 , 10 ~ 95% rh 0.03%/ (0 ~ 50 ) 10 ~ 500hz, 2g 10min./1cycle, 60min. each along x, y, z axes 160w single output medical type r p s - 1 6 0 s e r i e s universal ac input / full rangebuilt-in active pfc function protections: short circuit / overload / over voltage / 5"x3" compact size free air convection for 110w and 160w with 20.5 cfm forced air with power good and fail signal output 3 years warranty over temperature built-in remote sense function for 5~15vno load power consumption under 0.75w by ps-on control (g model) standby 5v@0.8a with fan, @0.6a without fan (g model) features : withstand voltage isolation resistance i/p-o/p:4kvac i/p-fg:1.5kvac o/p-fg:0.5kvac i/p-o/p, i/p-fg, o/p-fg:100m ohms / 500vdc / 25 / 70% rh safety & emc (note 4) protection environment current range (convection) ripple & noise (max.) note.2 rated power (20.5cfm) note.8 voltage tolerance note.3 power good / power fail power on: ps-on = "hi" or " > 2 ~ 5v" ; power off: ps-on = "low" or " < 0 ~ 0.5v" 500ms>pg>10ms pf>1ms function compliance to en55011 (cispr11), en55022 (cispr22) class b, en61000 -3-2,-3 mtbf dimension others compliance to en61000-4-2,3,4,5,6,8,11, en55024, en60601-1- 2, en61204-3, medical level, criteria a 230.5khrs min. mil-hdbk-217f (25 ) 127*76.2*34.6mm (l*w*h) 12 packing 0.32kg; 36pcs/12.5kg/0.79cuft note 1. all parameters not specially mentioned are measured at 230vac input, r ated load and 25 of ambient temperature. 2. ripple & noise are measured at 20mhz of bandwidth by using a 12" twisted pair- wire terminated with a 0.1uf & 47uf parallel capacitor. 3. tolerance : includes set up tolerance, line regulation and load regula tion. 4. the power supply is considered a component which will be installed into a fi nal equipment. the final equipment must be re-confirmed that it still me ets emc directives. 5. hs1,hs2 & hs3 can not be shorted. 6. derating may be needed under low input voltages. please check the derati ng curve for more details. 7. the rated power includes 5vsb @ 0.6a. 8. the rated power includes 5vsb @ 0.8a. for guidance on how to perform these emc tests, please refer to ?emi testing of c omponent power supplies.? (as available on http://www.meanwell.com) rps 160 g consumption < 0.75 w g: with 5vsb & no load power blank: basic function (without 5vsb) ps-on input signal (g model) 5v standby (g model) 5vsb : 5v@0.6a without fan, 0.8a with fan 20.5cfm ; tolerance 2%, ripple : 5 0mvp-p(max.) emc immunity emc emission
mechanical specification file name:rps-160-spec 2012-02-20 output derating vs input voltage input voltage (vac) 60hz 90 100 95 120 115 160 140 200 180 240 220 264 load (%) 90 100 80 70 60 50 40 unit:mm ambient temperature ( ) (horizontal) -20 0 10 20 30 40 50 60 70 derating curve ac input connector (cn1) : jst b3p-vh or equivalent dc output connector (cn2) : jst b8p-vh or equivalent pin no. pin no. 1,2,3,4 12 3 5,6,7,8 assignment assignment ac/l no pin ac/n -v +v mating housing mating housing jst vhr jst vhr or equivalent or equivalent terminal terminal jst svh-21t-p1.1 jst svh-21t-p1.1 or equivalent or equivalent power good connector(cn3):jst b4b-xh or equivalent pin no. 12 3 4 status pg gnd -s +s mating housing jst xhp or equivalent terminal jst sxh-001t-p0.6 or equivalent 5vsb connector(cn901) : jst b-xh or equivalent pin no. 1 2,4 3 assignment mating housing jst xhp jst sxh-001t or equivalent or equivalent terminal gnd 5vsb 5ma(max.) gnd ps/on ps/on power switching load (%) 20 40 60 80 100 with fan without fan 20.5cfm min. hs1 hs3 hs2 5cm fan 1 cn901 2 3 4 hs1,hs2,hs3 can not be shorted 160w single output medical type r p s - 1 6 0 s e r i e s block diagram +v -v pg i/p fg control o.v.p. pg fosc :100khz(5v) 70khz(12~48v) ps/on control ps/on pwm control power switching +5vsb circuit detection o.l.p. rectifiers & pfc filter filter circuit & & detection rectifiers rectifiers +5vsb emi filter +s -s 8 7 6 5 4 3 2 1 3 max. cn3 4 1 led cn2 cn1 fs1 fs2 1 66.2 34.6 76.2 23 cn901 5 3 2 5 117 127 svr1 4- 3.5
|
